Trigger with the Westley Richards 4 Bore.

I thought it would be quite nice to show you the 4 bore gun 'in hand' as it were, since the previous shots have all been hard to see exactly how large a gun it is. So here is Anthony 'Trigger' Tregear with the said gun in hand. Quite a handful isn't it!

13 Comments

Allan Kirk on September 28, 2015 at 6:03 pm

It's good to know that Birmingham will not be bothered by rampaging elephants in the future...

Reply
Ken on September 28, 2015 at 8:40 pm

Thank you for this pic! It does give a better scale on this gun. A nice piece of your team's gun making skills.

Ken

Reply
Larry on September 29, 2015 at 7:40 am

This photo still leaves a question to be answered... Which weighs more? :D

Reply
- Neill Clark on September 30, 2015 at 3:13 pm
  
  I reckon it's the gun, nobody should be that slim!
  
  Reply
Gary Duffey on September 29, 2015 at 7:46 am

The fact that Trigger's hand only reaches approximately half way around the gun at the forearm really gives a sense of the scale of this gun. Then I remembered that this is a droplock with single trigger! Really a great example of the relationship and intersection of the technology that W-R is using to scale guns and manufacture part sets with the traditional methods of hand fitting, filing, stocking, engraving and finishing. A remarkable testimony to all involved. I know the owner will be very happy!

Reply
Neill on September 29, 2015 at 9:24 am

Now that is what I call a gun! No danger of checking your swing with that thing, just a hernia trying to stop!

It really is magnificent, and good to see in hand as you can't really appreciate the size any other way. Makes me wonder about the 4 bore (DB?) rifle used by F C Selous,I wonder what the recoil on that was?

Reply
Fowad on September 29, 2015 at 10:02 am

How tall is trigger???

Reply
- Simon Clode on September 29, 2015 at 1:48 pm
  
  About 6'
  
  Reply
richard on September 30, 2015 at 10:04 am

What a beast ! Absolutley great . Fabulous workmanship. What ammo does it use ? I had a 4 bore single for flighting on the Scottish shore in the 70's.By then Eley had stopped their 4 Gauge with 3 oz load. I made my own-brass cases and used 4oz of BB propelled by 9drams of black powder. It kicked like a mule ! Have you pattern tested it , I assume it is full choke in both. How does it deal with restriction on use of lead ?

Great achievement,

Richard

Reply
- Simon Clode on September 30, 2015 at 4:37 pm
  
  Plastic cases have taken over from brass I regret to advise but that said they work and do the job. The large bore enthusiast Alan Myers loads these to various recipes and provided ourselves with a supply to make and test the gun and the client to shoot with. With regards the lead they will of course have to use Bismuth or such if they go to places lead is not allowed. It will be slightly less expensive than a Punt gun charge of Bismuth!
  
  Reply
- Nigel Barker on September 30, 2015 at 9:45 pm
  
  9 drams, 246 grains. I shoot cap-n-ball revolvers with 30 grains of black powder. That 9 drams is gonna make your eyes water.
  
  Reply
  - richard on October 1, 2015 at 1:45 pm
    
    I bet your ball doesn't weigh 4oz and leave the muzzle at just over 1000ft/sec !! The old gun weighed in at 15 lb and yes it made the eyes and much else water !!
    
    Reply
Craig L on October 11, 2015 at 8:39 am

Magnificent gun and lovely to still see big bores being made. Hope it gets to see a marsh or two! Graham Deakin on the Solway still makes up brass cases specific to the gun, along with re-loading tools and a fine job he does of them.

Reply